IG6000
Industrial Modem | Jump to other pages Radio Modems GSM Terminal - GSM Modems SMS I/O Controller CDMA Modem
Shorthaul Modem - Use Twisted Pair to
extend your RS-232 data distance to up to 10Km! |
Industrial
Modem IG6000 and IG1000 Modem Card (this
page) |
Hayes
command set: click
here 1 or here
2 or here
3 Rockwell chipset
commands (RC56D/RC336D & LD): click
here (.pdf file 492KB)
To
enter command mode: wait 3 seconds +++ wait 3 seconds, AT commands
follow.
Modem
Glossary - very comprehensive: click here
(opens new window)
For transmission distance over 2.5km. 1200 to 115.2kbps. Asynchronous, full/half duplex, plug-in screw terminals, ST/SMA fibre connectors. Power 1W.
ADAM-4541: Multi-Mode Fiber optic
to RS-232/422/485 converter
with mounting bracket. Wavelength 820 nm,Transmission
Distance 2.5 km, Optical Power Budget (attenuation) 12.5 dB
Consumption
1 W (typical); 1.5 W (max.)
More Data: click
here (jumps to ADAM Module page on this site.)
Serial
RS232 distance connections can be made by using an RS232 to RS485 Converters at
each end of a run of twisted pair cable.
Click
here for RS232 to RS485 Converters.
Prices (Australian dollars) do not include GST and may change without notice.
requires 9-15V DC, uses around 2.5W on-hook and 3W off-hook. Data: click here $199+GST 3/05
requires 12-18V DC, uses 3W on-hook and 3.5W off-hook. Data: click here $495+GST 3/05
IG6000
Industrial Modem requires 6 - 14.5V DC, uses 3W on-hook and can power
down to less than 0.1W in off-hook mode.
Watchdog timer, internal, to prevent
lock-up. See full data below (next item).
Modem Glossary - very comprehensive: click here (opens new window)
IG6000
Industrial Modem 33,600 bps data pump, and separate controller chip.
Uses the Motorola 68302 processor in 16 bit mode. x
Functionally similar to the NetComm SmartModem with additional flash memory
for voice message storage. Synchronous mode and leased line capability.
Dial in answer mode supported.
Low power mode.
The power input is protected
against transients, brown out, and has a wide input range of 6V to 14.5V DC, protected
against reverse polarity connection.
Power via serial connector: pin 9 and
a diode.
Requires 6 - 14.5V DC, uses 3W on-hook and can power down to less
than 0.1W in off-hook mode.
Port
speeds up to 232,400 bps are supported.
Two control line ports available,
via unused RS232 pins 12 and 13.
Each may be used either as an input for
monitoring, or as an output for control.
Two different stored
voice messages can be delivered in response to a control line operation.
PSTN, and 2 wire leased line with or without power are supported.
Multidrop
applications are also provided for using FSK modes up to 1200 bit/s line rate.
-10° C to +60° C. Data
on IG6000 Industrial modem: click here
Carton size: 240x190x90mm,
(1.03kg cubed weight)
Warranty period: 12 months. This can be extended
to three years by registering the product on the manufacturers
website (at very end of their home page).
IG6000 Industrial
modem:
Qty 1: $555+GST
| Qty 2-4: $545+GST | Qty
5-9: $535+GST | Qty 10+: $POA 10/06
Optional DC power versions: 9V to 28VDC or 36V to 72VDC: add $70.00+GST
IG6000
is supplied with:
Phone cable with Australian wall plug &
RJ11, 2m
Earthing green wire, 600mm,
Mains adaptor,
7.5VDC, 450mA
Floppy disk containing User Manual file (no programs),
Warranty card
The phone cable supplied with the IG6000 is suitable for use
with normal, dial-up, voice (PSTN) lines.
For leased line: a special phone
cable is available to connect the modem to a leased-line socket.
The IG 5500 modems
are cased, full duplex, asynchronous or synchronous data modems, with protection
and low power consumption. They are ideal for use in industrial applications where
high reliability under adverse operating conditions is required.
In
particular, the IG 5500's extensive Error correction, Data Compression and remote
site features make it ideal for unattended remote site applications.
Autoranging:
2400bps synch or async (V.22bis) 1200bps synch or async
(V.22 or Bell 212A) 300bps async (V.21 or Bell 103)
For
33.6Kbps, use IG6000, see above.
*
Greatly reduced approval time and costs
* Simply provide for the pinouts in
your design
* Logging Data real time vs onsite time
* Low cost management
and support
* Low cost networking
* End user accessibility and add-on
service possibility
V.92 connectivity, with upstream rates of up to 48Kbps
Supports 2-wire leased line
Class 1 fax
External flash ROM includes default
values for 29 countries
Local and International approvals include A-Tick,
CB Certified, EN55022 Class B, FCC Part 15 Class B
Small design (25mm x 65mm)
Development board also available – sold separately
Now you can slash the cost and time it used to take to add a modem to your design
The IG1000 is the first uniquely Australian developed modem that offers designers a space efficient communications module suitable for any data transfer application.
NetComm's IG1000 enables OEM's to integrate a variety of modem functions with the benefit of accessing real time data, low cost management / support, plus add-on service possibilities.
International EMC standards have been tested and certified, bringing the integration cost down for approval ratings on the finished product. Structured to fit into a generic industry footprint, this Conexant chipset product brings with it all the capabilities of a full hardware modem.
This product can be integrated into any device that requires data transfer via a PSTN connection, incorporating the latest V.92 technology to give your product the benefit of high upstream speeds (up to 48Kbps).
| This embedded technology comes with a developer's kit, which includes: * Board with footprint socket; * Greatly reduced approval time and costs | What’s so special about the NetComm IG1000? * V.92 – upstream rates up
to 48Kbps, QuickConnect, |
| Applications The IG1000 offers
a complete communications solution * meter reading |
Markets |
| Specifications * ITU-T V.92 with PCM upstream
rates up to 48 kbps, * Upgradeable Flash ROM |
* External flash ROM includes default values for 29 countries |
| Module Product Code: IG1000C50AU IG1000 V.92 Modem Module: $120+GST
IG1100
V.92 Modem Module – low profile: $120+GST |
IG1000 Module
Development Kit Board |
The IC-150 Short Haul Modem allows you to connect the RS-232 ports of remote devices for fast and easy file transfers and data sharing. Save on the cost of extra modems by installing a pair of these economical units and connecting them up with twisted pair cable. lhlo m n s zmxvzqd
Transfers can take take place over distances of up to 10km using either 4 wire (for Full Duplex) or 2 wire (for Simplex) telephone line. The nonpowered Line Driver facilitates efficient transmission and reception of serial data without requiring an external power source.
The unit drives your data at various speeds up to 19,200 bps over
distances up to 800m using 24-gauge
wire (transmitting at 110 bps over distances
up to 10km).
More information: click here
